Socket Scanner Accessories Troubleshooting

This page focuses on solving issues that affect the Socket barcode scanner’s optional charging dock, cradle, and QX stand accessories. If you’re experiencing an issue with the Socket barcode scanner, visit our Barcode Scanner Troubleshooting guide instead.

Table of Contents

Socket Charging Dock / Cradle Issues

Having trouble charging your barcode scanner using the charging dock or cradle? Check out some troubleshooting suggestions below.

The dock or cradle does not charge my barcode scanner.

  1. Make sure the power cable is plugged securely into the dock or cradle.
  2. Plug the power adapter into a different power outlet.
  3. Check that the scanner's charging pins are making contact with the charging pins on the dock or cradle.
  4. Make sure the battery cover screw on the back of the scanner is slightly recessed into the scanner. If it is not, gently tighten the screw.

My scanner turns off automatically on its own.

A scanner that is not being charged will power off after 2 hours of inactivity if it is paired with an iPad or after 5 minutes if it is unpaired. Follow these steps to power the scanner back on and, if needed, re-pair it.

  1. Hold the power button to turn on the scanner.
  2. Open the iPad's 'Settings' app.
  3. Tap 'Bluetooth'.
    Click to Enlarge
  4. Check the Socket device’s status.
    Click to Enlarge
  5. Continue troubleshooting below based on the scanner's status.
    • If the scanner is ‘Connected’, it is ready to be used again with the register.
    • If the scanner is ‘Not Connected’, follow these steps to disconnect and re-pair it.
    • If there is no status next to the Socket device, tap on it to connect.
    • If the Socket device is not listed, toggle the Bluetooth setting on.

To prevent the scanner from turning off in the future, place it on the charging cradle when not in use. If the scanner is not charging in the cradle, follow these steps above.

Socket QX Stand Issues

Having problems with your QX stand? Look no further. If you’re setting up for the first time, check out our QX Stand Setup guide.

The barcode scanner doesn’t fit in my stand.

  • The QX stand only works with the most up to date version of the Socket S740 scanner.
  • The compatible S740 look like the image below with its model number on the bottom of the scanner.
  • Purchase the appropriate model of scanner or contact Customer Care to check if your stand is within its return period.

    • My scanner won’t automatically scan barcodes.

    Most likely, your scanner was never placed in ‘Auto’ mode. If it was working at one point and suddenly stopped, however, someone may have removed it from the stand and pressed the scan trigger (this makes it return to ‘Normal’ mode).

    1. Print & scan the QR code for ‘Auto’ mode found on page 15 of the Quick Start Guide.
    2. Place the scanner in the stand making sure the charging pins align.
    3. The scanner beeps to let you know it’s connected to the stand.

      If your scanner doesn’t respond to these steps, you may have the wrong model. See above for details.

    My scanner doesn’t charge while it’s in the stand.

    Check each of the following to troubleshoot this issue:

  • Verify the charging pins on the scanner line up with those on the stand. The stand’s red LED should light up to signify charging.
  • Make sure the charging cable is plugged securely into the port on the stand. Also, be sure that you’re using the AC power adapter that shipped with the stand.
  • Test if the power outlet could be at fault. Try plugging the charging cable into a different outlet.
  • Check that you are using a compatible scanner (S740).

    • My scanner turns off automatically on its own.

    A scanner that is not being charged will power off after 2 hours of inactivity if it is paired with an iPad or after 5 minutes if it is unpaired. Follow these steps to power the scanner back on and, if needed, re-pair it.

    1. Hold the power button to turn on the scanner.
    2. Open the iPad's 'Settings' app.
    3. Tap 'Bluetooth'.
      Click to Enlarge
    4. Check the Socket device’s status.
      Click to Enlarge
    5. Continue troubleshooting below based on the scanner's status.
      • If the scanner is ‘Connected’, it is ready to be used again with the register.
      • If the scanner is ‘Not Connected’, follow these steps to disconnect and re-pair it.
      • If there is no status next to the Socket device, tap on it to connect.
      • If the Socket device is not listed, toggle the Bluetooth setting on.

    To prevent the scanner from turning off in the future, keep it in the QX stand when not in use. If the scanner is not charging in the stand, follow these steps above.