BOSSTAB Universal Tablet Stand Setup

The BOSSTAB Universal Tablet Stand, compatible with iPads and Android tablets 6″ and larger with a flat back, rotates 180°, conceals the tablet’s charging cable, and allows the tablet to be easily removed from the stand for added mobility. Set up the stand with the Freestanding Base to be able to move it around the countertop as needed, or mount the stand using the included materials to secure it in place.

Table of Contents

In the Box

The BOSSTAB Universal Tablet Stand and Freestanding Base ship in separate packaging and include the parts listed below.

BOSSTAB Universal Tablet Stand

Click to Enlarge
  • BOSSTAB Universal Tablet Stand
  • Allen Wrench
  • Torx Security Wrench
  • Adhesive Mount
  • 2 Wood Screws
  • 1 Hex Screw
  • Screw Mounting Guide
  • Getting Started Guide

    •    BOSSTAB Freestanding Base   

    Click to Enlarge
  • BOSSTAB Freestanding Base
  • 2 Machine Screws
  • Getting Started Guide

    • Stand Setup

    Install an iPad or Android tablet* in the stand, then attach the Freestanding Base or mount the stand using the included adhesive or screws. Lock the tablet in the stand with a security screw, or omit the screw to allow the tablet to be removed from the stand as needed.

    *Tablets must be 6″ or larger and have a flat back to be compatible with the stand.

    1. With the stand face down, use the star-shaped Torx wrench (included) to remove the security screw holding the top bracket in place.

      This screw is used in step 12 to optionally lock the tablet in the stand.

      Click to Enlarge
    2. Turn the stand over, and remove the top bracket.
      a  Lift the metal tab on the bracket until you feel resistance.
      Click to Enlarge
      b  While holding the tab, push the bottom of the bracket toward the tab until it unlocks from the stand.
      Click to Enlarge
      c  Lift the metal tab until the bracket separates from the stand.
      Click to Enlarge
    3. Attach the top bracket to your tablet.

      The BOSSTAB stand is compatible with iPads and Android tablets larger than 6″ with a flat back.

      a  Remove the backing from the 4 adhesive strips on the bracket.
      Click to Enlarge
      b  Lay the tablet facedown on a flat, soft surface.
      c  With the arrow on the back of the bracket pointing toward the top of the tablet, place the bracket adhesive-side down in the center of the tablet.
      The top of the tablet is the end opposite the charging port.
      Click to Enlarge
      d  Hold the bracket firmly, but gently, in place for 30 seconds.
      Avoid pressing too hard as this could damage the screen of the tablet.
    4. Use a Phillips screwdriver (not included) to remove the inner 4 screws holding the case to the stand, then lift the case off the stand.

      These screws will be used to reattach the case in step 9.

    5. Place the stand on the countertop in the specific orientation for the desired setup.
      • To allow the stand to rotate, position it so the notch in the bottom faces the cashier. This ensures the tablet charging cable will be hidden from customers as it exits the stand through the notch.
      • To prevent the stand from rotating, position it so the notch in the bottom points to the cashier’s left as they face customers. This allows the stand rotation to be locked, but the tablet charging cable may be visible to customers as it exits the stand through the notch.
    6. Feed the charging cable for the tablet through the stand, with the tablet connector end coming out the top of the stand.

      Use the charging cable included with the tablet as other cables may not fit through the stand. If necessary, connect an extension cable to lengthen the charging cable.

      Click to Enlarge
    7. Follow the steps in one of the sections below to attach the Freestanding Base or mount the stand.
      a  Attach the Freestanding Base to allow the stand to move freely on the countertop; OR
      b  Use adhesive to mount the stand to the countertop without drilling holes; OR
      c  Use screws to mount the stand to the countertop for a more secure solution.
    8. (Optional) If desired, lock the stand rotation.

      The stand must be positioned as described in step 5 above to complete this step.

      a  Rotate the top of the stand so the BOSSTAB logo faces the cashier.
      b  Insert the hex screw included with the stand into the hole in the stand as shown below and tighten it using the Allen wrench (included).
      Click to Enlarge
    9. Place the case back on the stand in landscape orientation, then reinsert and tighten the 4 screws removed in step 4.

      To change the tablet orientation later, remove the tablet and case, then repeat this step with the case in the opposite orientation.

      Click to Enlarge
    10. Fit the charging cable into the notch on the case.
      Click to Enlarge
    11. Align the top bracket attached to the tablet with the case, then place the tablet on the case.
      Click to Enlarge
    12. (Optional) Reinsert and tighten the security screw removed in step 1 to secure the tablet in the stand.

      Skip this step, if desired, to allow the tablet to be easily removed from the stand as needed.

    13. Wait 24 hours for the adhesive to cure before using the stand.

      Failure to complete this step may cause the tablet to separate from the stand while in use.

    Having issues with the BOSSTAB Universal Tablet Stand? Visit our troubleshooting guide for help.

    Attach Freestanding Base

    Attach the Freestanding Base to the BOSSTAB stand to allow the stand to move freely on a countertop. The Freestanding Base does not secure the stand to the counter.

    Before following the steps below, you must complete steps 1 – 6 in the ‘Stand Setup’ section above.

    1. Feed the charging cable for the tablet down through the hole in the center of the Freestanding Base.
      Click to Enlarge
    2. Align the screw holes on the bottom of the stand with those on the base.
        Bottom of Stand  

      Click to Enlarge
      Freestanding Base

      Click to Enlarge

    3. Rotate the top of the stand until both screw holes are visible through the top.
      Click to Enlarge
    4. Insert the machine screws included with the Freestanding Base through the holes in the stand and tighten using a Phillips screwdriver (not included).
      Click to Enlarge
    5. Follow steps 8 - 13 in the 'Stand Setup' section above to finish setting up the stand.

    Mount Using Adhesive

    Mount the stand using the included adhesive to securely adhere the stand to a countertop without drilling holes. If necessary, the adhesive can later be removed using an oscillating tool (sold separately).

    Before following the steps below, you must complete steps 1 – 6 in the ‘Stand Setup’ section above.

    1. Fit the charging cable for the tablet into the grooves in the bottom of the stand.
      Click to Enlarge
    2. Make sure there is enough slack in the cable to plug it into the tablet once the stand is fully assembled.

      After mounting the stand to the countertop in step 8 below, you will be unable to adjust the cable.

    3. Wipe the bottom of the stand and the countertop with an alcohol wipe (not included), then wait for both surfaces to dry.
    4. Remove the white backing from the included adhesive mount.
    5. Align the adhesive with the cutouts on the bottom of the stand.
    6. Stick the adhesive to the stand and hold firmly in place for 30 seconds.
      Click to Enlarge
    7. Remove the remaining backing from the adhesive.
    8. Place the stand on the countertop and hold firmly in place for 30 seconds.
    9. Follow steps 8 - 13 in the 'Stand Setup' section above to finish setting up the stand.

    Mount Using Screws

    Mount the stand using the included wood screws to more securely attach the stand to a countertop. Drilling holes into the counter is required to mount the stand in this way.

    Before following the steps below, you must complete steps 1 – 6 in the ‘Stand Setup’ section above.

    1. Use the included mounting guide to drill holes into the counter that align with the 2 screw holes in the bottom of the stand.
    2. (Optional) Drill an additional hole to feed the charging cable for the tablet through the counter.
    3. Fit the charging cable into the grooves in the bottom of the stand, OR feed it through the hole drilled in step 2.
      Click to Enlarge
    4. Rotate the top of the stand until the 2 screw holes are visible through the top.
      Click to Enlarge
    5. Align the screw holes on the bottom of the stand with those drilled in the counter.
      Click to Enlarge
    6. Insert the wood screws included with the stand through the holes in the top of the stand, then tighten the screws to secure the stand to the counter.
      Click to Enlarge
    7. Follow steps 8 - 13 in the 'Stand Setup' section above to finish setting up the stand.